乳酸钠和双乙酸钠对熟火腿的抑菌作用和感官品质的影响

添加不同含量的乳酸钠、双乙酸钠或柠檬酸钠,按照标准配方制作熟火腿.制备后,一部分产品直接进行感官分析,另一部分煮熟、切碎、均匀接种L monocytogenes和L curvatus,真空包装后在4℃储存.与对照组相比,添加2.5％～3.3％的乳酸钠抑制了L monocytogenes和L curvatus的生长.添加0.2％的双乙酸钠对火腿的口感和气味有负面影响.0.1％和0.2％的双乙酸钠对L curvatus没有抑制作用.另一方面,添加1％的缓冲柠檬酸钠可以促进L monocytogenes的生长.     

回转窑动态检测及托轮磨削的应用

我公司3#回转窑Φ4.8 m×74 m，三档支撑，带液压挡轮，斜度4％，设计产量5?000~6?000 t/d。回转窑运行过程中，筒体存在晃动现象，在窑尾密封处观察较为明显，晃动幅度约±20 mm，甚至导致三档托轮基础及周围栏杆也随之晃动。     

火麻仁油微乳凝胶面膜的制备及初步评价

目的:制备火麻仁油微乳凝胶补水面膜并对其理化性质、保湿性和抗氧化活性进行评价.方法:通过伪三元相图确定火麻仁油微乳最佳处方,采用单因素及正交试验优化火麻仁油微乳凝胶处方,载入保湿活性物质制得火麻仁油微乳凝胶面膜并对其质量、稳定性、保湿性和抗氧化活性进行评价.结果:火麻仁油微乳最佳处方:火麻仁油0.2％、PEG-20氢化蓖麻油0.53％、1,3丙二醇0.27％.火麻仁油微乳凝胶最佳处方为卡波姆-940含量1％,丙三醇含量5％,稀释倍数30倍.制得的微乳凝胶澄清透明、涂展性较好、易清洗、不油腻;平均粒径为(30.91±0.31)nm,PDI为0.299±0.017,电位为(-3.54±0.43)mV;黏度为494725.15 mPa·s;pH值为5.50±0.01;保湿效果优于市售某凝胶面膜;火麻仁油微乳凝胶面膜对DPPH自由基清除率高于火麻仁油毛油,质量浓度为6 mg·mL-1时可达62.39％,IC50为3.71 mg·mL-1.结论:火麻仁油微乳凝胶面膜安全、稳定,制备工艺简单,对皮肤具有良好的补水和抗氧化效果,具备开发和推广的价值.     

性能数据驱动的机械产品关键设计参数识别方法

利用运行数据识别产品设计缺陷或薄弱环节是产品开发和更新换代的主要模式,也是保证产品服役性能稳定的重要途径.提出了一种性能数据驱动的产品关键设计参数(薄弱环节)识别方法.首先,利用极限学习机算法划分运行工况,提出了基于核主成分分析和高斯混合模型的多工况性能退化评估方法,消除了工况变化对性能退化评估的影响,得到性能退化严重的关键功能模块;其次,对性能监测数据进行聚类分析,识别出与模块性能退化密切相关的关键性能监测参数;最后,建立了“性能监测参数—性能参数—设计参数”三者之间的关联关系,识别出导致性能严重退化的关键设计参数.以某大吨位履带起重机作业机构为例,验证了方法的有效性.     

典型化工生产单元操作一体化实训室数字化课程学习系统建设

基于对典型化工生产单元操作一体化实训室数字化课程学习系统建设实践，将复杂且具有高度危险性的化工生产单元操作过程教学、培训等，构建成一个高度信息化的综合平台，利用视频、动画、微课、仿真等软硬件组成数字化的学习系统，即解决了学校资源、资金、场地、安全等的不足，方便学生随时随地学习，又解决了教师枯燥难教的困境，同时也解决了校内学资源碎片化、校际缺少共享等问题，为教学、培训、社会服务等提供便捷途径。     

Influence analysis of bracket set on seismic performance of steel eave columns in Chinese traditional style buildings

This paper presents influence analysis of bracket set on seismic performance of steel eave columns in Chinese traditional style buildings. Eight 1/1.5‐scale steel eave columns were constructed and tested under low cyclic reversed loading, including 4 specimens with bracket set and 4 specimens without bracket set. Based on the analysis of the strain of the specimens, the failure modes of the specimens were obtained. In addition, the hysteresis loops, skeleton curves, degradations of stiffness and strength, ductility, and dissipation capacities of the specimens were analyzed. Bracket set changed the force transfer mechanisms and failure modes of the specimens and had a significant influence on the seismic performance of the specimens. Compared with the specimens without bracket set, the yielded and ultimate bearing capacities of the specimens with bracket set improved by 30.7% and 24.0%, respectively. And also, the stiffness of the specimens with bracket set at the yielded and ultimate points increased by 52.8% and 135.6%. The dissipation capacities of the specimens with bracket set were 2.12 times those of the specimens without bracket set at yielded load. However, the ductility of the specimens with bracket set slightly decreased by 8.5%. It was shown that the seismic performance of the specimens with bracket set was better than that of the specimens without bracket set. The work in this paper provides a basis for further theoretical study on the seismic performance of steel eave columns in Chinese traditional style buildings.     

硫酸铵法利用中低品位锂瓷土矿制备碳酸锂技术研究

针对江西宜丰地区氧化锂质量分数<2.0%以下中低品位锂瓷土矿,研究了硫酸铵法提取碳酸锂技术路线。首先,利用二步焙烧工艺,有利于脱氟、提高锂浸出率,并且能够有效防止结窑现象发生。在浸出液除杂过程中,采用成矾除铝的方法将大量溶出的铝离子转变为KAl（SO₄）₂·12H₂O、NH₄Al（SO₄）₂·12H₂O等有价值复盐,规避了传统石膏法产生的大量固废,有70%的铝离子被转变为矾盐晶体,同时带出大量的结晶水,减轻后续浓缩压力,对比传统的石膏法产生大量固废而言,其优点是显而易见的。碳化反应产品的XRD以及氧化锂含量分析表明,碳酸锂的纯度达到99%以上,全程锂收率为50%~60%。作为提锂实验对比,采用宜春414矿锂质量分数为4.0%的锂云母,由于414矿样中铝的相对含量更低,导致相同的除杂难度下得到的414矿样中浸出液锂离子浓度更高,浓缩倍数更小,414矿样的锂回收率更高。实验结果表明,中低品位锂瓷土提锂的工艺规律,通过适当改变参数,能够应用于难度更低的高品位的锂云母提锂过程。     

与椭圆封头连接的N型固定管板计算

近年来,因化工生产工艺需求,管程侧与椭圆封头连接的N型管板特殊结构被广泛使用。结合GB/T 151—2014《热交换器》标准对管板进行计算,并对管板与壳体连接处的局部结构进行应力分析,得到了合理的计算结果,使设计文件更加完善,确保了设备安全运行。     

Comparative studies on thermal and toughness properties of polybenzoxazine composites with two functionalized graphene oxides

Abstract

Graphene oxide (GO) was functionalized by polyether amine (PEA) via two methods which were one-pot modification in acetone (GON) and two steps with the intermediate product of GOCO-Cl generated (GONS). There were more PEA successfully grafted onto GO for GONS than GON. The onset polymerization temperatures of the benzoxazine (Bz) composites decreased by the inclusion of 1?wt% of GO, GON or GONS. Thermal stability of the polybenzoxazine (PBz) composites was significantly improved indicated from the increase of weight loss temperature. T₁₀, T₂₀ and T₅₀ values of the composites with GONS were higher than that of the others. Toughness of PBzs may be enhanced by the incorporation of nanofillers, and GONS had stronger interfacial interaction with PBz matrix than GON.